to the product overview

Please select the industry:

Emtec Electronic presents its Softness Tester in North America

The German company emtec Electronic GmbH will attend the Techtextil North America 2019 in Raleigh, North Carolina, USA from February 26th to 28th, together with the representative Technidyne Corporation. At exhibition booth no. 1443, the company will present its innovative softness testing instrument for the textile and nonwovens industry:73

The TSA – Softness Analyzer enables an objective evaluation of the softness, roughness and stiffness of a textile fabric. Included into the softness measurement is the measurement of the viscoelastic, elastic and plastic properties, which are represented by the elasticity, plasticity and hysteresis. With an extra module, the compressibility can be measured.

New measuring method to evaluate the Hand Feel (HF) of Fiber Resources

The TSA – Tissue Softness Analyzer represents a nearly perfect simulation of the human hand and shows excellent results in measuring base tissue and finished tissue products (toilet paper, handkerchiefs, facials). In case of hand sheets made in the lab, the device also convinced in measuring the influence of pulp quality (short fibers), refining or softener. But it was limited until now to measure the influence of different compositions of long and short fibers to the softness of hand sheets, and thus, to predict the haptic quality of tissue products.73

The German company emtec Electronic, which developed the original TSA – Tissue Softness Analyzer, upgraded the device with a new sensor design and Marcel Prinz, now Doctoral student at the University of Applied Sciences in Munich, started his master thesis with several tests with the upgraded prototype of the TSA in 2017. He proved and optimized the new TSA measuring method for hand sheets, which enables the measurement of the influence of different fiber mixes (long and short fibers ratio) to the quality of the hand sheet. By the new sensor design and an improved measuring method it was possible to gain very accurate and reliable results with a good correlation to the expectations and the haptic tests. This available information allows a quality forecast for the actual base tissue and finished product, if a certain fiber mix is used.

The new TSA measuring method opens completely new possibilities in saving costs and resources in the production, and it leads to an efficiency increase in the process and product optimization. Especially pulp mills, research institutes and the R&D labs of tissue mills and chemical suppliers waited for such results. Since the last quarter of 2018, the full upgraded TSA version for such measurements, but also the upgrade of an existing standard TSA, is available.

Emtec Electronic GmbH at the ATIP 2018 in Grenoble

Also, this year in November, emtec Electronic GmbH will attend the ATIP 2018 in Grenoble in France, together with its French representative ODL Paper Service. At exhibition booth no. 2 the company will present a variety of testing instruments by which the complete production process – from the wet end to the finished products – can be controlled and guided in the right direction, to get an efficient process and the best possible quality with the lowest possible costs. To meet steadily the changing demands and requirements in the paper and board industry, the focus is again on further developments and innovations.FPA touchCAS touch Website

Displayed at the booth will be the state-of-the-art CAS touch! to measure the particle charge and the FPA touch! to measure the surface charge of fibers (zeta potential). Both devices help to get information about the efficiency of the chemicals, which are added during the paper, board and tissue production.

Besides this, the EST12 emtec Surface & Sizing Tester is shown. A device to determine important and for the converting relevant paper surface properties such as surface hydrophobia / sizing as well as the surface porosity, which influence printability, coatability and gluability of paper and board.

The ACA Ash Content Analyzer enables the determination of the mineral filler content without combustion, that means without destruction of the samples, within seconds. Both, the total mineral filler content, as well as the individual filler components (e.g. calcium carbonate, kaolin/talcum, titanium dioxide, iron oxide) and their percentage distribution are given.

Especially for tissue and nonwoven products, the TSA Tissue Softness Analyzer gives reliable and objective information about the three basic parameters, which determine the human feeling, the softness, roughness and stiffness. From these three, an overall hand feel value can be calculated. The availability of the three individual parameters opens a huge amount of chances for the optimization of the tissue production and converting processes.